Enhancing Polyvinyl Alcohol Nanocomposites with Carboxy-Functionalized Graphene: An In-Depth Analysis of Mechanical, Barrier, Electrical, Antibacterial, and Chemical Properties.

To enhance the various properties of polyvinyl alcohol (PVA), varying concentrations of carboxy-functionalized graphene (CFG) were employed in the preparation of CFG/PVA nanocomposite films. FTIR and XRD analyses revealed that CFG, in contrast to graphene, not only possesses carboxylic acid group but also exhibits higher crystallinity. Mechanical testing indicated a notable superiority of CFG addition over graphene, with optimal mechanical properties such as tensile and yield strengths being achieved at a 3% CFG concentration. Relative to pure PVA, the tensile strength and yield strength of the composite increased by 2.07 and 2.01 times, respectively. XRD analysis showed distinct changes in the crystalline structure of PVA with the addition of CFG, highlighting the influence of CFG on the composite structure. FTIR and XPS analyses confirmed the formation of ester bonds between CFG and PVA, enhancing the overall performance of the material. TGA results also demonstrated that the presence of CFG enhanced the thermal stability of CFG/PVA nanocomposite films. However, analyses using scanning electron microscopy and transmission electron microscopy revealed that a 3% concentration of CFG was uniformly dispersed, whereas a 6% concentration of CFG caused aggregation of the nanofiller, leading to a decrease in performance. The incorporation of CFG significantly enhanced the water vapor and oxygen barrier properties of PVA, with the best performance observed at a 3% CFG concentration. Beyond this concentration, barrier properties were diminished owing to CFG aggregation. The study further demonstrated an increase in electrical conductivity and hydrophobicity of the nanocomposites with the addition of CFG. Antibacterial tests against E. coli showed that CFG/PVA nanocomposites exhibited excellent antibacterial properties, especially at higher CFG concentrations. These findings indicate that CFG/PVA nanocomposites, with an optimized CFG concentration, have significant potential for applications requiring enhanced mechanical strength, barrier properties, and antibacterial capabilities.

Polymer Packaging through the Blending of Biowaste Oyster Shell and Low-Density Polyethylene: A Sustainable Approach for Enhanced Food Preservation.

This research delves into the impact of incorporating thermally treated oyster shell powder (TOS), a biowaste filler, into low-density polyethylene (LDPE) to develop a LDPE/TOS blend, aiming at enhancing food packaging materials. The LDPE/TOS blend portrays advantageous characteristics such as augmented mechanical strength, thermostability, crystallinity, water absorption, and improved hydrophobicity with TOS content up to 50%. Microstructure analysis reveals a transition from a sparse to a more interconnected structure, contributing to the amplified tensile strength. The blend demonstrates increased barrier properties against water vapor transmission, which is attributed to elongated diffusion paths induced by the TOS particles. Application of the blend material in vegetable preservation trials manifested a substantial reduction in water loss compared to pure LDPE or no packaging. This biowaste-based blend film extends the shelf-life of chicken significantly when compared to that of pure LDPE. Importantly, the LDPE/TOS blend exhibits excellent antibacterial properties against both Escherichia coli and Staphylococcus aureus.

Improving Mechanical and Barrier Properties of Antibacterial Poly(Phenylene Sulfide) Nanocomposites Reinforced with Nano Zinc Oxide-Decorated Graphene.

Nano zinc oxide-decorated graphene (G-ZnO) was blended with polyphenylene sulfide (PPS) to improve its tensile, thermal, crystalline, and barrier properties. The properties of neat PPS and PPS/G-ZnO nanocomposites were characterized and compared using various tests, including tensile tests, scanning electron microscopy, X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis, evaluation of Escherichia coli inhibition, and barrier performance. The results demonstrated that G-ZnO played a crucial role in heterogeneous nucleation and reinforcement. When the concentration of G-ZnO was 0.3%, the tensile strength, elongation at break, thermostability, crystallinity, and water vapor permeability coefficients (WVPC) approached their maximum values, and the microscopic morphology changed from the original brittle fracture to a relatively tough fracture. In addition, when G-ZnO was added to PPS at a ratio of 0.3%, the tensile strength, elongation at break, and WVPC of PPS were increased by 129%, 150%, and 283%, respectively, compared to pure PPS. G-ZnO endowed the nanocomposites with antibacterial properties. The improvement in barrier performance can be attributed to three reasons: (1) the presence of G-ZnO extended the penetration path of molecules; (2) the coordination and hydrogen bonds between PPS polymer matrix and G-ZnO nanofiller narrowed the H2O transmission path; and (3) due to its more hydrophobic surface, water molecules were less likely to enter the interior of PPS/G-ZnO nanocomposites. This study provides valuable insights for developing high-performance PPS-based nanocomposites for various applications.

Characterization and Morphology of Nanocomposite Hydrogels with a 3D Network Structure Prepared Using Attapulgite-Enhanced Polyvinyl Alcohol.

In this investigation, purified attapulgite (ATT) and polyvinyl alcohol (PVA) were utilized to fabricate nanocomposite hydrogels and a xerogel, with a focus on studying the impact of minor additions of ATT on the properties of the PVA nanocomposite hydrogels and xerogel. The findings demonstrated that at a concentration of 0.75% ATT, the water content and gel fraction of the PVA nanocomposite hydrogel reached their peak. Conversely, the nanocomposite xerogel with 0.75% ATT reduced its swelling and porosity to the minimum. SEM and EDS analyses revealed that when the ATT concentration was at or below 0.5%, nano-sized ATT could be evenly distributed in the PVA nanocomposite xerogel. However, when the concentration of ATT rose to 0.75% or higher, the ATT began to aggregate, resulting in a decrease in porous structure and the disruption of certain 3D porous continuous structures. The XRD analysis further affirmed that at an ATT concentration of 0.75% or higher, a distinct ATT peak emerged in the PVA nanocomposite xerogel. It was observed that as the content of ATT increased, the concavity and convexity of the xerogel surface, as well as the surface roughness, decreased. The results also confirmed that the ATT was evenly distributed in the PVA, and a combination of hydrogen bonds and ether bonds resulted in a more stable gel structure. The tensile properties exhibited that when compared with pure PVA hydrogel, the maximum tensile strength and elongation at break were achieved at an ATT concentration of 0.5%, indicating increases of 23.0% and 11.8%, respectively. The FTIR analysis results showed that the ATT and PVA could generate an ether bond, further confirming that ATT could enhance the PVA properties. The TGA analysis showed that the thermal degradation temperature peaked when the ATT concentration was at 0.5%, providing further evidence that the compactness of the nanocomposite hydrogel and the dispersion of the nanofiller was superior, contributing to a substantial increase in the mechanical properties of the nanocomposite hydrogel. Finally, the dye adsorption results displayed a significant rise in dye removal efficiency for methylene blue with the increase in the ATT concentration. At an ATT concentration of 1%, the removal efficiency rose by 103% compared with that of the pure PVA xerogel.

Mechanical, Hydrophobic, and Barrier Properties of Nanocomposites of Modified Polypropylene Reinforced with Low-Content Attapulgite.

Attapulgite (ATT) has never been used as a barrier additive in polypropylene (PP). As a filler, ATT should be added in high content to PP. However, that would result in increased costs. Moreover, the compatibility between ATT and the PP matrix is poor due to the lack of functional groups in PP. In this study, carboxylic groups were introduced to PP to form a modified polypropylene (MPP). ATT was purified, and a low content of it was added to MPP to prepare MPP/ATT nanocomposites. The analysis from FTIR indicated that ATT could react with MPP. According to the results of oxygen and water permeability tests, the barrier performance of the nanocomposite was optimal when the ATT content was 0.4%. This great improvement in barrier performance might be ascribed to the following three reasons: (1) The existence of ATT extended the penetration path of O2 or H2O molecules; (2) O2 or H2O molecules may be adsorbed and stored in the porous structure of ATT; (3) Most importantly, -COOH of MPP reacted with -OH on the surface of ATT, thereby the inner structure of the nanocomposite was denser, and it was less permeable to molecules. Therefore, nanocomposites prepared by adding ATT to MPP have excellent properties and low cost. They can be used as food packaging materials and for other related applications.

Barrier Properties and Hydrophobicity of Biodegradable Poly(lactic acid) Composites Reinforced with Recycled Chinese Spirits Distiller's Grains.

Adding natural biomass to poly(lactic acid) (PLA) as a reinforcing filler is a way to change the properties of PLA. This paper is about preparing PLA/biomass composites by physically melting and blending Chinese Spirits distiller's grains (CSDG) biomass and PLA to optimize the composite performance. Composites of modified PLA (MPLA) with varying amounts of CSDG were also prepared by the melt-mixing method, and unmodified PLA/CSDG composites were used as a control group for comparative analysis. The functional groups of MPLA enhanced the compatibility between the polymer substrate and CSDG. The composite water vapor/oxygen barrier and mechanical properties were studied. It was found that the barrier and mechanical properties of MPLA/CSDG composites were significantly improved. SEM was adopted to examine the tensile section structure of the composites, and the compatibility between the filler and the matrix was analyzed. An appropriate amount of CSDG had a better dispersibility in the matrix, and it further improved the interfacial bonding force, which in turn improved the composite mechanical properties. X-ray diffraction, thermogravimetric analysis, and differential scanning calorimetry were conducted to determine the crystalline properties and to analyze the stability of the composites. It was found that the CSDG content had a significant effect on the crystallinity. Barrier and biodegradation mechanisms were also discussed.

Barrier performance and biodegradability of antibacterial poly(butylene adipate-co-terephthalate) nanocomposites reinforced with a new MWCNT-ZnO nanomaterial.

A new nanomaterial or nano-filler in the form of multiwalled carbon nanotube-zinc oxide (MWCNT-ZnO) was synthesized for the purpose of modifying poly(butylene adipate-co-terephthalate) (PBAT) and its derivative (modified PBAT or MPBAT) through a melt-blending method (MPBAT was obtained by introducing maleic anhydride groups into PBAT). The effect of the new nano-filler on the properties of resultant nanocomposites was determined from the characterization of mechanical properties, morphology, crystallinity, thermal stability, barrier properties, hydrophilicity, conductivity, antibacterial property, and biodegradability. The results showed that MPBAT nanocomposites had stronger mechanical properties, better barrier properties, and higher electrical conductivity than PBAT nanocomposites. Scanning electron microscopy illustrated that MWCNT-ZnO had better compatibility with MPBAT than with PBAT. At 0.2% MWCNT-ZnO, the MPBAT/MWCNT-ZnO nanocomposite film exhibited the greatest mechanical properties (17.74% increase in tensile strength, 22.17% in yield strength, and 14.29% in elongation at break). When the MWCNT-ZnO content was 0.4%, the nanocomposite film demonstrated the best water vapor barrier ability (an increase of 30.4%). The MPBAT/MWCNT-ZnO film with 0.6% MWCNT-ZnO turned out to have the best oxygen barrier performance (an increase of 130% relative to pure PBAT). It was shown from the results of antibacterial evaluation that the new nanomaterial could impart PBAT and MPBAT with antibacterial activity. The biodegradability tests indicated that an MWCNT-ZnO content of 0.2% could slightly reduce the biodegradability, and when the content was higher than 0.2%, the weight loss rate would increase.

Polyurethane/Nanosilver-Doped Halloysite Nanocomposites: Thermal, Mechanical Properties, and Antibacterial Properties.

In this study, the researchers successfully embellished the surface of halloysite (Ag/HNTs) with silver using halloysite, silver nitrate (AgNO3), and polyvinylpyrrolidone (PVP). The researchers then prepared polyurethane that contained pyridine ring by using 4,4'-diphenylmethane diisocyanate (MDI) and polytetramethylene glycol (PTMG) as the hard chain segment and the soft chain segment of polyurethane (PU), as well as 2,6-pyridinedimethanol (2,6-PDM) as the chain extension agent. This was followed by the preparation of Ag/HNTs/PUs nanocomposite thin films, achieved by mixing Ag/HNTs with different ratios into polyurethane that contains pyridine ring. First, the Ag/HNTs powders were analyzed using energy-dispersive X-ray spectroscopy, X-ray diffraction, and transmission electron microscopy. Subsequently, Fourier-transform infrared spectroscopy was used to examine the dispersibility of Ag/HNTs in PU, whereas the thermal stability and the viscoelasticity of Ag/HNTs/PU were examined using thermal gravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis. When the mechanical properties of Ag/HNTs/PU were tested using a universal strength tester, the results indicated a maximum increase of 109.5% in tensile strength. The researchers then examined the surface roughness and the hydrophobic ability of the Ag/HNTs/PU thin films by using atomic force microscopy and water contact angle. Lastly, antibacterial testing on Escherichia coli revealed that when the additive of Ag/HNTs reached 2.0 wt%, 99.3% of the E. coli were eliminated. These results indicated that the addition of Ag/HNTs into PU could enhance the thermal stability, mechanical properties, and antibacterial properties of PU, implying the potential of Ag/HNTs-02 as biomedicine material.

Characterization of network bonding created by intercalated functionalized graphene and polyvinyl alcohol in nanocomposite films for reinforced mechanical properties and barrier performance.

Graphene that consists of less than 10 layers is expensive; moreover, it tends to agglomerate. These disadvantages restrict its utility. In this regard, the present study aimed to reduce the number of layers of a functionalized graphene (FG) with 10-30 layers to less than 10 layers by using an ultrasonic processor. We prepared nanocomposite films of polyvinyl alcohol (PVA) incorporated with FG by a simple hydrothermal method and ultrasonic dispersion. Oxygen transmission rate and water vapor permeability were considerably increased on account of modifying PVA with FG. Furthermore, the mechanical properties, thermostability, and barrier properties were improved. The barrier efficiency of the nanocomposites at different temperatures remained high for long periods of operation because of the network bonding. A simple procedure involving relatively low-cost nanomaterials could unlock the potential of nanocomposite FG/PVA films in the fields of coating, packaging, and semiconductor materials.

Synthetic Environmentally Friendly Castor Oil Based-Polyurethane with Carbon Black as a Microphase Separation Promoter.

This study created water polyurethane (WPU) prepolymer by using isophorone diisocyanate, castor oil, dimethylolpropionic acid, and triethanolamine (TEA) as the hard segment, soft segment, hydrophilic group, and neutralizer, respectively. TEA, deionized water, and carbon black (CB) were added to the prepolymer under high-speed rotation to create an environmentally friendly vegetable-oil-based polyurethane. CB served as the fortifier and promoter of microphase separation. Fourier transform infrared spectroscopy was performed to elucidate the role of H-bond interactions within the CB/WPUs. Additionally, atomic force microscopy was conducted to determine the influence of H-bond interactions on the degree of microphase separation in the WPU. Furthermore, this study used four-point probe observation to discover the materials' conductivity of CB in the WPU. Thermogravimetric analysis and dynamic mechanical analysis were performed to measure the thermal properties of the CB/WPUs. The mechanical properties of CB/WPUs were measured using a tensile testing machine. The CB/WPUs were also soaked in 1 wt.% NaOH solution for different amounts of time to determine the degradation properties of the CB/WPUs. Finally, scanning electron microscopy was performed to observe the topography of the CB/WPUs after degradation.

Organocatalyzed ring-opening copolymerization of α-bromo-γ-butyrolactone with ε-caprolactone for the synthesis of functional aliphatic polyesters - pre-polymers for graft copolymerization.

Diphenyl phosphate (DPP) was exploited as an organocatalyst to synthesize copolymers by ring-opening polymerization with α-bromo-γ-butyrolactone (αBrγBL) and ε-caprolactone (εCL) as monomers and polyethylene glycol (PEG) as initiator. The conversion rates of monomers and molecular weights of copolymers synthesized under different conditions were determined by 1H-NMR. The 1H-NMR results showed that the copolymers of αBrγBL and εCL initiated by PEG (PEGCB) were successfully synthesized and the conversions of εCL were relatively high (＞70%), while the conversions of αBrγBL were relatively low (＜26%). The highest molar ratio of αBrγBL to εCL units in these copolymers is 0.17, when the copolymerization was carried out at 100℃ for 17h. The bromine atoms hanged on the chain of the copolymers PEGCB provide a good opportunity to construct graft copolymers via atom transfer radical polymerization (ATRP). The subsequent grafting of 2-(dimethylamino)ethyl methacrylate (DMAEMA) was conducted by using PEGCB3 as macroinitiator, CuBr/N,N',N',N",N"- pentamethyldiethylenetriamine (PMDETA) as catalysts and toluene/anisole as solvents via ATRP. According to the analysis of 1H-NMR, the grafting efficiency, grafting ratio and grafting frequency were 22.4%, 160.7% and 1133.8, respectively.

Antibacterial Property and Cytotoxicity of a Poly(lactic acid)/Nanosilver-Doped Multiwall Carbon Nanotube Nanocomposite.

A novel method was used to synthesize a nanosilver-doped multiwall carbon nanotube (MWCNT-Ag), and subsequently, the novel poly(lactic acid) (PLA)- and MWCNT-Ag-based biocompatible and antimicrobial nanocomposites were prepared by melt blending. Based on energy dispersive X-ray spectrometry images, an MWCNT-Ag was successfully synthesized. The effect of the MWCNT-Ag on the PLA bionanocomposites was investigated by evaluating their thermal and mechanical properties, antifungal activity, and cytotoxicity. The nanocomposites exhibited a high degree of biocompatibility with the MWCNT-Ag content, which was less than 0.3 phr. Furthermore, tensile strength testing, thermogravimetric analysis, differential scanning calorimetry, and antibacterial evaluation revealed that the tensile strength, thermostability, glass transition temperature, and antibacterial properties were enhanced by increasing the MWCNT-Ag content. Finally, hydrolysis analysis indicated that the low MWCNT-Ag content could increase the packing density of PLA.

Biocompatibility and characterization of polylactic acid/styrene-ethylene-butylene-styrene composites.

Polylactic acid (PLA)/styrene-ethylene-butylene-styrene (SEBS) composites were prepared by melt blending. Differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WXRD) were used to characterize PLA and PLA/SEBS composites in terms of their melting behavior and crystallization. Curves from thermal gravimetric analysis (TGA) illustrated that thermostability increased with SEBS content. Further morphological analysis of PLA/SEBS composites revealed that SEBS molecules were not miscible with PLA molecules in PLA/SEBS composites. The tensile testing for PLA and PLA/SEBS composites showed that the elongation at the break was enhanced, but tensile strength decreased with increasing SEBS content. L929 fibroblast cells were chosen to assess the cytocompatibility; the cell growth of PLA was found to decrease with increasing SEBS content. This study proposes possible reasons for these properties of PLA/SEBS composites.

Preparation and Characterization of Bioplastic-Based Green Renewable Composites from Tapioca with Acetyl Tributyl Citrate as a Plasticizer.

Granular tapioca was thermally blended with poly(lactic acid) (PLA). All blends were prepared using a plasti-corder and characterized for tensile properties, thermal properties and morphology. Scanning electron micrographs showed that phase separation occurred, leading to poor tensile properties. Therefore, methylenediphenyl diisocyanate (MDI) was used as an interfacial compatibilizer to improve the mechanical properties of PLA/tapioca blends. The addition of MDI could improve the tensile strength of the blend with 60 wt% tapioca, from 19.8 to 42.6 MPa. In addition, because PLA lacked toughness, acetyl tributyl citrate (ATBC) was added as a plasticizer to improve the ductility of PLA. A significant decrease in the melting point and glass-transition temperature was observed on the basis of differential scanning calorimetry, which indicated that the PLA structure was not dense after ATBC was added. As such, the brittleness was improved, and the elongation at break was extended to several hundred percent. Therefore, mixing ATBC with PLA/tapioca/MDI blends did exhibit the effect of plasticization and biodegradation. The results also revealed that excessive plasticizer would cause the migration of ATBC and decrease the tensile properties.

Poly[[µ-(3-amino-pyridine)-κ(2)N:N'-µ-chlorido-chlorido(N,N'-dimethyl-formamide-κO)nickel(II)] N,N'-dimethyl-formamide monosolvate].

The title compound, {[NiCl(2)(C(5)H(6)N(2))(C(3)H(7)NO)]·C(3)H(7)NO}(n), is a two-dimensional polymer in which the Ni(II) atom is coordinated by two N atoms from two 3-amino-pyridine ligands, one O atom from a dimethyl-formamide (DMF) group, one terminal Cl and two bridging Cl atoms in a distorted octa-hedral geometry. The Ni(II) atoms are bridged by the 3-amino-pyridine ligands [Ni⋯N = 6.7048 (3) Å] and Cl(-) atoms [Ni⋯N = 3.5698 (3) Å], forming (4,4) two-dimensional nets. The DMF solvent mol-ecule and the non-bridged Cl(-) ions participate in N-H⋯O and N-H⋯Cl hydrogen bonds with the amino groups.

Poly[(µ(3)-quinoline-6-carboxyl-ato-κ(3)N:O:O')silver(I)].

In the title coordination polymer, [Ag(C(10)H(6)NO(2))](n), the Ag(I) cation is coordinated by two O atoms and one N atom from three 6-quinoline-carboxyl-ate anions in a distorted T-shaped AgNO(2) geometry, in which the O-Ag-O angle is 160.44 (9)°. The 6-quinoline-carboxyl-ate anion bridges three Ag(+) cations, forming a nearly planar polymeric sheet parallel to (101). The distance between Ag(+) cations bridged by the carboxyl group is 2.9200 (5) Å. In the crystal, π-π stacking is observed between parallel quinoline ring systems, the centroid-centroid distance being 3.7735 (16) Å.